Viking Clip · Rainscreen · reviewed September 14, 2026
What the manufacturer actually lists
System literature offers domestic and tropical species; those offerings are not approval of every board sold under the same name.
Named species / categories
Ipe · Western Red Cedar · Cumaru · Redwood · Massaranduba · Cypress · Garapa · Cambia (thermally modified poplar) · Mahogany · Thermally modified maple · Teak · Thermally modified ash · Sapele · African mahogany
Explicit exclusions
No exhaustive exclusion list found. Absence of a prohibition is not approval.
Conditions that change the answer
- The original Viking Clip needs furring. VC2 is the separately described no-batten option.
- The published 1/8-inch abutment clearance is not the field reveal. The 3/4-inch top ventilation opening is not a clip dimension.
- Exact alloy, clip dimensions, screw size, interface tolerances and tested wall capacity remain unverified in the reviewed material.
CONNECTION REFERENCE / REVISION reference-3
Viking / on-batten rainscreen
Reference reconstruction. Unverified production dimensions are withheld.
Loading reference model…Inspect a component
? Production profile — A manufacturer reference section is distinct from the board supplied to your project. Unverified envelopes contain no invented production groove.
Open supporting source ↗Visible-interface reconstruction. Upper rear tongue, sloping shoulder and lower engagement groove are shown in section. This is an explanatory milling profile; obtain the supplied mill drawing before machining or confirming fit.
On-batten clip with an H-shaped engagement section and single fixing opening. The upper tongue and lower groove of adjacent siding boards engage opposite sides of the clip; separate furring creates the wall cavity.
Sources, confidence and reconstructed details
Owner-supplied front, rear, side and installation photographs, September 16, 2026. Milled siding section reconstructed from architectural assembly references. Visual reconstruction; no supplied-production fit certification.
Open the manufacturer reference ↗ · Full hardware evidence record
Reference-inferred or illustrative features
- Clip radii, extrusion details and dimensions are reference-reconstructed
- Milled siding: upper rear tongue, sloping shoulder, lower rear engagement groove and overlapping face
- Illustrative profile proportions; use the supplied mill drawing for cutter setup and tolerances
- Representative screw geometry; selected kit alloy and embedment remain unresolved
Supplied production fit: pending. A recognizable model does not change the compatibility result. The board shown explains a manufacturer interface, not approved Ipe Woods milling.
A · Verified technical model — Geometry from approved CAD or dimensional drawings; only verified dimensions are displayed.
B · Reference reconstructed — Source-faithful visual model. Inferred details are recorded and unverified manufacturing dimensions are withheld.
C · Illustration — Explains an assembly principle; never presented as an exact branded product.
TECHNICAL MODEL / VERIFICATION GATE
Manufacturer evidence & supplied-fit review
Reference reconstructions explain the documented mechanism. Their inferred details are labeled separately; matching the actual supplied board, accessory SKU and current instructions remains a separate review.
- Exact system
- Viking Clip — original
- Manufacturer / system record
- Viking Clip
- Application
- Rainscreen
- Installation reference
- Published documents linked below; these do not verify the supplied board profile.
- Geometry status
- Reference reconstruction where available; current production geometry remains unverified
- Production groove / profile
- Verification pending — nominal size does not establish engagement.
- Published screw configuration
- Stainless screw is described, but an exact diameter, length, alloy and fastening schedule were not established. Obtain the current original-Viking submittal.
This exact siding system requires its own profile and mounting documents. No generic wall detail is substituted.
Inspect the hardware reference library
DeckWise official CAD archive · Board-profile source of truth
Manufacturer installation evidence, manufacturer geometry and supplied production fit are independent verification states. No generated image establishes any of them.
Dimensions belong to different parts
Installed gap, clip size, board thickness and groove cut are separate measurements. Mill tolerances and the sold accessory match remain separate approvals.
| Measurement | Inches | Millimeters | Applies to / limitation |
|---|---|---|---|
| Recommended support centers | 16 | 406.4 | Original installation guide gives a 24-inch maximum; project design may be more restrictive. |
| End-to-abutment clearance | 0.125 | 3.175 | Not the board-to-board reveal. |
| Top / below-window ventilation opening | 0.75 | 19.05 | Original guide detail, not a universal cavity depth. |
| Clip / groove / reveal dimensions | Unverified | — | Needs Verification. No dimensions are inferred from the product images. |
Metric values are calculated conversions, not added manufacturing precision.
The screw is part of the system
Stainless screw is described, but an exact diameter, length, alloy and fastening schedule were not established. Obtain the current original-Viking submittal.
Installation sequence
Complete window/door flashing and weather barrier details first.
Use properly anchored vertical furring and the manufacturer’s matched siding profile.
Set the first row level. Fit clips and successive boards according to the exact system submittal.
Maintain screened ventilation paths and specified abutment clearances. Resolve top-board face fastening.
Do not release a purchase or installation schedule until clip, screw, profile and wall-load details are confirmed.
Manufacturer instructions for this record
Viking Clip system and species offerings ↗
Viking Clip installation guidelines ↗
Read the current instructions for the purchased model. This reference does not certify wall capacity, warranty coverage or an Ipe Woods milling match.